SIMIX Multi-Surface CoatingHelps
Your Air Conditioning Units
Run More Efficiently
Saving You Time and Money
Over time, the aluminum inside your A/C unit starts to erode and forms a layer of oxidation that becomes an insulator. That layer slows down the process of dissipating the heat.
Simix Multi-Surface Coating penetrates this layer of oxidation and converts it from an insulator to a conductor, thus restoring efficiency.
Simix Multi-Surface Coating also contains nano particles of titanium dioxide, which break down surface tension on fins, resulting in an immediate increase of air movement across the surface. The faster you can get the aluminum fins to dissipate heat, the quicker the fins pull heat from the copper tubing.
Simix Multi-Surface Coating
• Lowers your energy costs
• Easy on-site application, new and old units
• Units stay cleaner longer
• Longest lasting and most affordable coating
• The first coating to improve heat transfer and air flow
• Extends the life of the condensing coil
• Minimizes salt build-up on coastal installations
• No special training needed to use the cleaner and apply the coating
• Typical ROI is less than 6 months
How does Simix Multi-Surface Coating work? Simix is nano-engineered, and works in the world of particles that are one thousand times smaller than the human eye can see. Simix contains sub-nano and nano-particles which bind together in a tight structure. The coating is applied to the condensing coil fins and as it’s sprayed on, it wicks into the microscopic voids between the fin and tube connection. It fills the voids that are created between the fin and tube connection during the first 90 days of operation. It immediately improves heat transfer between the tube and the fin. The coating is very slick and improves air flow by breaking surface tension. More air can move through the opening because there is no friction on the fins. The more CFM pulled through a unit, the more efficient the unit becomes. In most cases, the unit is restored back to its original specifications.
How do I use Simix Multi-Surface Cleaner and apply Simix Multi-Surface Coating? It’s simple. Pull the unit’s breaker. Apply Simix Multi-Surface Cleaner with a misting sprayer. Allow to sit for a couple minutes. Then thoroughly rinse with water. Replace the unit’s breaker and turn on to dry for approximately ten minutes. Pull the unit’s breaker again, and then use a high pressure/low volume sprayer to evenly apply Simix Multi-Surface Coating over the coils, fins, fans and cabinet. Spray both sides of coils, fins, fans and cabinet. Spraying the cabinet and supports will extend their life. Replace the unit’s breaker and run unit for 30 minutes to cure the coating.
Bent fins cost you money. How does Simix help you restore them? Repair the bent fins by misting a small amount of Simix Multi-Surface Coating above, on and below the damaged area using a trigger spray bottle. Insert the appropriate sized fin comb under the damaged area and pull upwards through the damaged area; repeat starting from the top and pulling back down through the same damaged area. This technique cuts the normal repair time by over 90%.
How long does Simix Multi-Surface Coating last? We recommend that you re-apply every year, but you can go for several years depending on the amount of salt and pollutants in your environment.
What kind of savings can I expect? On a new unit, we recommend applying the product after 90 days of operation. You can expect a savings of at least 3% the first year. Existing installations have shown savings of 18% or more. Cleaner units require less maintenance.
How long does it take to start working? The unit’s efficiency decreases temporarily as the coating dries, then will increase within hours and will continue to improve over the next week as Simix Multi-Surface Coating fully cures.
How does Simix Multi-Surface Coating make it easier to clean the unit? First of all, units just stay cleaner once coated with Simix. That’s because the coating breaks down the exhaust gas emissions and significantly limits the ability of dirt and debris from attaching. A/C units in climates that get a lot of rain will be kept clean by moisture pulled into the fins by the fan. In drier climates, rinsing with a garden hose periodically will keep the fins clean. In areas with excessive airborne pollution, a small amount of diluted Simix Cleaner followed by rinsing with a garden hose will be all you need to assure the unit is operating at maximum efficiency. (Using any other type of cleaner may result in the destruction of Simix Multi-Surface Coating.)
Who can apply Simix Multi-Surface Coating? Your own staff can do it. It's easy. You can also have A/C service provider apply Simix.
What makes Simix Multi-Surface Coating environmentally friendly? The nano particles of titanium dioxide embedded in Simix Multi-Surface Coating react to UV rays from the sun to break down hydrocarbons in the air. Hydrocarbons are created by exhaust emissions from cars, trucks and airplanes. Basically, Simix helps break down air pollution.